PST joins DwyerOmega. Read more>
Compact 316 SS Ultrasonic NO Level Switch
COMPACT ULTRASONIC, SOLID STATE LIQUID LEVEL SWITCH
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Easy to Install
- No Moving Parts
- Epoxy-Sealed Integral Electronics with Sensor
- Low-Cost Replacement to Mechanical Float
LVSW-720 Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Process Connection Size
Media Type
Max Operating Pressure
Max Process Temperature
Wetted Materials
Process Connection Type
Switch Rating and Type
Features
The LVSW-710/720 compact solid state liquid level switch is a great replacement for mechanical float-type liquid level devices. The switch employs proven ultrasonic technology and solid state integral electronics in a small package. The LVSW-710/720 provides reliable operation in virtually any liquid, regardless of viscosity. This eliminates problems of stickiness and failure rate due to finite mechanical life inherent in the mechanical float design. The combination of fully epoxy-sealed electronics and ultrasonic sensing technology will provide years of maintenance-free service
SPECIFICATIONS
Repeatability: 2 mm or better
Delay: 0.5 sec
Input Power: 5 to 30 Vdc
Leakage Current: Less than 50 uA
Wire Length: 300 mm (12")
Protection: Transient, reverse polarity
Sensor: 316 LSS
Temperature: -29 to 80°C (-20 to 176°F)
Pressure: Up to 250 psig (1724 kPa)
Mounting: ¼ or ½ NPT (depending on model number)
Relay Output: 1 A SPST, NO
SPECIFICATIONS
Repeatability: 2 mm or better
Delay: 0.5 sec
Input Power: 5 to 30 Vdc
Leakage Current: Less than 50 uA
Wire Length: 300 mm (12")
Protection: Transient, reverse polarity
Sensor: 316 LSS
Temperature: -29 to 80°C (-20 to 176°F)
Pressure: Up to 250 psig (1724 kPa)
Mounting: ¼ or ½ NPT (depending on model number)
Relay Output: 1 A SPST, NO
Rated 4 out of
5
by
Cable User from
Missing document info
I couldn't find any documentation that describes the cable/wire information (gauge, insulation/jacket type, etc), so I wrote this review to provide that:
The cable that was attached to mine is a Belden 9535, and Belden provides a nice spec sheet on their website.
Date published: 2017-06-02
Rated 5 out of
5
by
James1 from
Great Sensor - Would Like to See Future Variations
Sensor operating voltage is versatile
(5-30VDC). My application uses 6VDC.
Sensor is compact enough to make it work in tight areas. It is 1/2” NPT and 3” long.
I would love to see the following variations in the future:
1) Make the wiring via a connector instead of cable coming out connector. This will allow easy removal.
2) If point 1 is not possible, make the cable longer, maybe 6-ft.
3) Make another sensor with longer length; may be 2-in longer. This will allow the shorter one to be used for level control, while the longer used for low level alarm.
Date published: 2021-03-11
Do you have an intrinsically safe/ explosion rated version of this sensor?
Unfortunately, we do not have or carry ultrasonic level switches rated for hazardous applications.
Date published: 2020-03-02
Is the alarm point at the centerline of the body? Does the rotation of the sensor affect the alarm point? The manual is very unclear and has no indication of mounting orientation.
Thanks for the inquire
The entire gap would have to be filled to trigger an alarm condition. Additionally, the units can be mounted in any orientation.
Date published: 2022-03-11
I have some foam and bubbles on my liquid. Do you think this sensor will trigg when the foam will be in the gap?
Thank you for your inquiry. If the foam dissipates then, there is no premature trigger. The foam will have to be dense enough to cause the switch to actuate the relay.
Date published: 2024-05-30
Does the sensor need to be installed a certain distance from walls or obstacles to ensure proper functionality?
Thank you for your inquiry about the level switch. It does not have to install a specific distance from the side wall. As long s liquid can make contact, it will change stateas on the relay.
Date published: 2022-10-10
Can the sensor be mounted vertically?
Unfortunately, these level switches are only intended for side mounting. Please consider the LVSW-701 as an alternative that can be mounted in any direction.
Date published: 2021-11-17
What Controller or other device does this get attached to?
Thank you for your inquiry. Unfortunately, there are no other device attached or link wit this level switch.
Date published: 2020-12-08
Will this switch operate in a engine coolant type of liquid ie glycol ?
Thank you for your inquiry! Yes, this switch will operate effectively with engine coolant.
Date published: 2021-05-24
Can you provide a CE declaration for the LVSW-710?
Yes, we can. Send us an email to flow@omega.com and we can reply with a copy.
Date published: 2020-06-09
